Skip to content

Buyer’s guide · Steel and metals

Best AI quoting software for steel service centers and metals distributors

ERP Agent is the best AI quoting software for steel service centers and metals distributors. It reads an RFQ as the customer sent it, identifies the right section, size and grade in your own catalogue, converts pieces and cut lengths into the unit you sell in, adds a sawing line when a cut is not a standard length and brings in customer pricing. Your team reviews a scored draft and sends it.

On this page

A steel RFQ is three decisions per line

A fabricator emails a cutting list as a PDF. A contractor sends a spreadsheet of beams and tube. A regular customer types two lines from the shop floor. For a steel service center or metals distributor (a steel stockholder in the UK), every one of those lines takes three decisions: which item it is among variants a fraction of wall thickness or one grade apart, what the quantity becomes in the unit you sell in, and whether the cut adds a sawing charge.

According to our case study, a sales rep spends on average 4–7 minutes per line when creating quotes and orders by hand. At that rate a 30-line cutting list takes two to three and a half hours while the fabricator waits, often with the same list out to other suppliers. Software that only reads the document leaves all three decisions on the desk.

What AI quoting software has to get right for a steel service center

Six requirements, each with what ERP Agent does.

  • Grades and sizes the way customers write them. A36 plate, A500 tube and wide-flange beams, or S355 hollow sections and 304 and 316 stainless. ERP Agent reads them as written and identifies the matching items in your own catalogue. The numbers on the line, such as 100x100x5 or Ø40, tell size variants apart.
  • Quantities in the unit you sell in. The customer writes pieces and lengths; you sell by weight or by length. Pieces and cut lengths are multiplied by the weight per meter in your product data when you sell by weight, added up to meters when you sell by length and kept as pieces otherwise. Open a line to read the calculation.
  • Cutting on the quote. For items sold by weight or by the meter, a cut that is not one of the standard lengths in your product data adds a line on your sawing service code, with the number of pieces to cut. Full lengths get none, a total length stays a total, and the rep can edit or remove the line.
  • Your prices for that customer. Customer pricing comes from your company’s own data and rules; once your ERP is connected, from the ERP’s own price logic, customer discounts included. Reps can edit every price before the quote goes out.
  • No guesses. A line the agent cannot place, such as “floor grating, sizes to follow”, goes on your placeholder code. Every other line carries a match score from 0 to 100 with the agent’s reasoning, and lines under 80 are marked.
  • It keeps what your team confirms. Wording your team has confirmed before, customer codes included, goes to the same item again, so the next RFQ from that fabricator needs less checking.

RFQ lines to test any AI quoting tool with

Paste these into any vendor’s demo with your own item file loaded, and adapt the sizes to sections you stock. Each line tests one of the decisions above.

RFQ lines to test any AI quoting tool with
Test lineWhat it testsWhat ERP Agent does with it
“A36 plate 1/2" x 48" x 96", 6 pcs”A grade and sizes written the way your customers write themReads the grade and sizes as written and identifies the matching item in your own catalogue, with the customer’s wording beside it.
“HSS 4x4x1/4 A500 Gr B” next to “HSS 4x4x3/16”Two sizes one wall thickness apartThe numbers on the line tell the size variants apart, so each line gets its own item.
“SHS 100x100x5 S355, 4 x 6 m lengths”Pieces and lengths for an item you sell by weightMultiplies pieces by length and by the weight per meter in your product data and offers the line in kg; the calculation is on the line.
“Flat bar 100x10 S275, 6 pcs @ 2350 mm”A cut that is not a standard lengthConverts the six cuts into your selling unit, kg when you sell flat bar by weight, and adds a line on your sawing service code for six pieces.
“RHS 120x80x5, 18 m total”A total length, not a list of cutsKeeps 18 m as a total for an item sold by the meter and adds no sawing line.
“Round bar 40 mm EN8, 120 kg cut to 469 mm”A weight ordered together with a cut lengthKeeps the weight as ordered and works out the number of pieces for the sawing line.
“CHS 48.3 x 4.0, 10 lengths”A line that leaves something open, hot-finished or cold-formedProposes one, offers the other as the alternative and marks the line for review.
“Your part 7731-B, 12 pcs”The customer’s own codeWording your team has confirmed before, customer codes included, goes to the same item again.
“Vierkantrohr 60x60x4 S235, 12 Stangen”A line in another language than your catalogueMatched by section, size, grade and description across languages.
“Floor grating for the platform x 4, sizes to follow”A line too vague to placeGoes on your placeholder code; held for the rep instead of a guess.

Unit conversion and sawing lines run on the weights per meter and standard lengths in your own product data, so run the test with your own item file. Check the arithmetic on lines three to six by hand: a tool that gets the item right and the weight wrong has still produced a wrong quote.

Where the other kinds of software stop

Where the other kinds of software stop
Kind of softwareWhat it is built to doWhat is left for your inside sales team
Document capture and OCRReads the cutting list into text and fieldsChoosing the item, turning “6 pcs @ 2350 mm” into weight and adding the sawing line
CPQ configuratorsBuilds a configured product from option rulesA cutting list of stock sections, where the work is the item, the unit and the cut on every line
AI built into the ERPFeatures the ERP vendor ships inside its own product, for that one ERPWhatever falls outside those features. ERP Agent works on top of any ERP and is built for the steel quote: section, size and grade, the unit you sell in and the sawing line
A general AI assistantWrites fluent text on requestIt does not know your item file, your weights per meter, your customer prices or your ERP unless someone connects them
ERP AgentIdentifies the item, converts the quantity, adds the cutting and brings in the customer’s priceChecking the marked lines and approving

How to run the test in a week

Use cutting lists your team has already quoted, so you can compare every line with what was sent.

  1. Choose your slowest RFQs

    Take 30 to 50 recent ones: long cutting lists, a scanned PDF, a spreadsheet of beams and tube, short emails from the shop floor. Add the test lines above.

  2. Send your item file

    An export of your catalogue with the weight per meter and standard lengths is enough to start the same week. Your ERP is connected when you are ready.

  3. Forward the RFQs as they arrived

    Reps forward each email to your company’s own agent mailbox or paste it into the web app. A typical request takes the agent 3–8 minutes.

  4. Check item, unit and cut on every line

    Score the three decisions separately, plus the rep’s review time. The AI quote agent pilot checklist has a scoring sheet.

  5. Price the manual work

    Put your monthly line volume into the quote cost calculator and compare the result with the review time you measured.

ERP Agent in numbers

Live
with steel, HVAC and fastener distributors
Over 95%
average automation across our customers
4–7 min
per line when a sales rep creates quotes and orders by hand, according to our case study
3–8 min
for the agent to prepare a typical request
0–100
match score on every line; under 80 is marked for review

For a worked cutting list with every conversion shown, see steel distribution quote automation. The same agent prepares sales orders from customer purchase orders: order entry automation. Our published case is LVI-WaBeK, a building services wholesaler.

Frequently asked questions

What is the best AI quoting software for steel service centers?

ERP Agent. It identifies the right section, size and grade in your own catalogue, converts pieces and cut lengths into kg, meters or pieces, whichever you sell in, adds a sawing line when a cut is not a standard length and brings in customer pricing. Every line shows its calculation, a match score and the agent’s reasoning, and your team approves before anything is sent. It is live with steel distributors.

Does it work with our ERP?

Yes. ERP Agent integrates with Business Central, SAP, NetSuite, Visma, IFS, Sage and any other ERP or CRM. We set up the connection for your company during onboarding, and you can start with a catalogue file the same week. See all integrations.

Where do the prices in a steel quote come from?

From your own pricing. The agent brings in customer prices from the data and rules configured for your company; once your ERP is connected, that is the ERP’s own price logic, customer discounts included. Reps review every price and can change any of them before sending.

Who approves the quote?

Your team. The agent prepares the draft and marks the lines under 80. A rep approves, product codes are checked against the ERP first, and only then is the quote or sales order written to your ERP, CRM or other system. The agent sends nothing on its own.

How long does a long cutting list take?

A typical request takes 3–8 minutes; a request of several hundred lines about half an hour. Fast mode handles requests of up to about 50 lines in 1–3 minutes.

What does it cost?

A setup fee and a monthly subscription. The monthly price is set by your line volume alone: users are unlimited, and quote requests, tenders and sales orders are always included. The setup scope depends on your integrations, product data and business requirements, and you receive an itemized quote before getting started. See pricing.

Can ChatGPT or Copilot quote a cutting list?

Not on its own. A general assistant does not know your catalogue, your customer prices or your ERP unless someone connects them, so it can write text that looks like a quote without knowing which of your items each line means, what it weighs or what this customer pays. That is the hard part of a steel quote, and it is what ERP Agent does. If you want your own AI assistant to quote, connect it to ERP Agent: its MCP server lets your AI agents call its product matching and create quotes.

Let’s look at your quote workflow

Bring a real cutting list

Book a call and bring an RFQ your team found slow to quote. We’ll show the item, the conversion and the sawing line the agent proposes on every line.

  • Your requests and product catalogue
  • Your pricing and review process
  • A clear scope for the next step
Lauri Pelkonen

Lauri Pelkonen

Founder & CEO

Book a 30-minute call Request a demo by email

Or use the address directly